HoneyTrap Development

Troubleshooting kubeadm

ebtables or ethtool not found during installation

If you see the following warnings while running kubeadm init

[preflight] WARNING: ebtables not found in system path                          
[preflight] WARNING: ethtool not found in system path                           

Then you may be missing ebtables and ethtool on your Linux machine. You can install them with the following commands:

# For ubuntu/debian users, try 
apt install ebtables ethtool

# For CentOS/Fedora users, try 
yum install ebtables ethtool

Pods in RunContainerError, CrashLoopBackOff or Error state

Right after kubeadm init there should not be any such Pods. If there are Pods in such a state right after kubeadm init, please open an issue in the kubeadm repo. kube-dns should be in the Pending state until you have deployed the network solution. However, if you see Pods in the RunContainerError, CrashLoopBackOff or Error state after deploying the network solution and nothing happens to kube-dns, it’s very likely that the Pod Network solution that you installed is somehow broken. You might have to grant it more RBAC privileges or use a newer version. Please file an issue in the Pod Network providers’ issue tracker and get the issue triaged there.

kube-dns is stuck in the Pending state

This is expected and part of the design. kubeadm is network provider-agnostic, so the admin should install the pod network solution of choice. You have to install a Pod Network before kube-dns may deployed fully. Hence the Pending state before the network is set up.

HostPort services do not work

The HostPort and HostIP functionality is available depending on your Pod Network provider. Please contact the author of the Pod Network solution to find out whether HostPort and HostIP functionality are available.

Verified HostPort CNI providers:

For more information, read the CNI portmap documentation.

If your network provider does not support the portmap CNI plugin, you may need to use the NodePort feature of services or use HostNetwork=true.

Pods are not accessible via their Service IP

Many network add-ons do not yet enable hairpin mode which allows pods to access themselves via their Service IP if they don’t know about their podIP. This is an issue related to CNI. Please contact the providers of the network add-on providers to get timely information about whether they support hairpin mode.

If you are using VirtualBox (directly or via Vagrant), you will need to ensure that hostname -i returns a routable IP address (i.e. one on the second network interface, not the first one). By default, it doesn’t do this and kubelet ends-up using first non-loopback network interface, which is usually NATed. Workaround: Modify /etc/hosts, take a look at this Vagrantfileubuntu-vagrantfile for how this can be achieved.

TLS certificate errors

The following error indicates a possible certificate mismatch.

# kubectl get po
Unable to connect to the server: x509: certificate signed by unknown authority (possibly because of "crypto/rsa: verification error" while trying to verify candidate authority certificate "kubernetes")

Verify that the $HOME/.kube/config file contains a valid certificate, and regenerate a certificate if necessary. Another workaround is to overwrite the default kubeconfig for the “admin” user:

mv  $HOME/.kube $HOME/.kube.bak
mkdir -p $HOME/.kube
sudo cp -i /etc/kubernetes/admin.conf $HOME/.kube/config
sudo chown $(id -u):$(id -g) $HOME/.kube/config

Errors on CentOS when setting up masters

If you are using CentOS and encounter difficulty while setting up the master node, verify that your Docker cgroup driver matches the kubelet config:

docker info | grep -i cgroup
cat /etc/systemd/system/kubelet.service.d/10-kubeadm.conf

If the Docker cgroup driver and the kubelet config don’t match, change the kubelet config to match the Docker cgroup driver. The flag you need to change is --cgroup-driver. If it’s already set, you can update like so:

sed -i "s/cgroup-driver=systemd/cgroup-driver=cgroupfs/g /etc/systemd/system/kubelet.service.d/10-kubeadm.conf

Otherwise, you will need to open the systemd file and add the flag to an existing environment line.

Then restart kubelet:

systemctl daemon-reload
systemctl restart kubelet

The kubectl describe pod or kubectl logs commands can help you diagnose errors. For example:

kubectl -n ${NAMESPACE} describe pod ${POD_NAME}

kubectl -n ${NAMESPACE} logs ${POD_NAME} -c ${CONTAINER_NAME}